Updated November 2026

If your RV has no power when plugged in, the problem is almost always in one of a few places: the campground pedestal, the shore cord, the main breaker or GFCI, or the converter that feeds your 12V system. This guide walks you through checking each one in order, so you can restore power without guessing or calling a technician for a problem you can fix yourself.

Start by Checking the Campground Pedestal

Before you open anything on the RV, confirm that the pedestal is actually live. Plug a lamp or a phone charger directly into the pedestal’s outlet. If it doesn’t work, the issue is at the site, not your rig. Ask the campground office to check the pedestal’s breaker, since many parks share circuits between sites. If you want more background on the connection itself, see What Is Shore Power RV? A Clear Guide for Campers (2026).

Shopping for one? See our guide: 6 Best 30 Amp RV Power Plugs for Campers and Motorhomes (2026).

Inspect the Shore Cord and Connections

Next, look at the cord and both ends. Scorched plastic, melted prongs, a cracked housing, or a loose fit in the pedestal all point to a bad connection that can cut power or create a fire risk. Wiggle the plug while the cord is connected. If the lights flicker or go out, the cord or receptacle is the likely culprit. Replace damaged cords rather than taping them. A lot of trouble traces back to this step, and it’s one of the quickest checks you can do. For more on this, see No Shore Power to RV: 6 Causes and Fixes for Campers.

Check the Main Breaker, GFCI and Transfer Switch

Open the main electrical panel and look at the main breaker and any GFCI outlets inside the RV. A tripped GFCI is one of the most common causes of no power, especially in bathrooms, kitchens and outdoor outlets. Press the reset button firmly. If the main breaker is off, switch it on. If your rig has an automatic transfer switch, confirm it is set to shore power and not generator or inverter. Some owners find the switch stuck or sluggish, which can make the coach look dead even when the pedestal is live.

Quick checklist

  1. Test the pedestal with a known-good device.
  2. Inspect the shore cord, plug and receptacle for heat damage.
  3. Confirm the main breaker is on.
  4. Reset any tripped GFCI outlets.
  5. Verify the transfer switch is on shore power.

Test the Converter and 12V系统

Many RVs use a converter to turn incoming AC into 12V DC for lights, the water pump and the control panel. If the AC appliances work but the 12V lights and panel are dead, the converter or its fuse is the likely problem. Check the converter’s fuses and look for error codes on its display if it has one. Some converters have a battery-disconnect or a low-voltage shutdown that can make the coach seem unpowered. A battery that is deeply discharged can also prevent the converter from restarting properly, so check the house battery voltage too. If you suspect the converter, see Troubleshooting RV Power Converter: A Step-by-Step Guide for Campers.

Common Mistakes to Avoid

  • Assuming the campground is fine without testing the pedestal first.
  • Resetting a GFCI repeatedly without finding the fault, which can hide a real wiring problem.
  • Using an adapter or extension cord that is undersized for your rig’s load.
  • Ignoring a warm plug or a burning smell at the connection.
  • Forgetting that a dead house battery can mimic a total power failure.

A simple outlet tester or a voltage meter lets you check pedestals and outlets in seconds, which speeds up every step above. View on Amazon

A replacement shore power cord in the correct amperage is worth keeping on hand if your current one shows wear. View on Amazon

FAQ

Why does my RV have no power when plugged in but the campground is working?

The most common causes are a tripped GFCI, a tripped main breaker, or a damaged shore cord. Check those first before looking at the converter or wiring.

Can a dead house battery stop power when plugged in?

Yes. A very low battery can keep the converter from powering the 12V system, so lights and the control panel may seem dead even while AC appliances run. Charging or testing the battery often clears this up.

When should I call a professional?

If you smell burning, see scorched connections inside the panel, or the breaker trips repeatedly after resetting, stop and consult a qualified RV technician or electrician. Electrical faults can be dangerous, so don’t keep resetting a problem you can’t identify.

Conclusion

Most no-power problems come down to the pedestal, the cord, a tripped breaker or GFCI, or the converter. Working through these in order usually finds the fault in under an hour. If the problem continues after these checks, a professional inspection will help you avoid a bigger repair.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our off-grid power for camping, RV & vanlife guides, checking product details against manufacturer specifications and owner feedback.