Updated November 2026
If your RV is not getting power when plugged in, the cause is usually one of four things: no power at the pedestal, a tripped breaker, a damaged shore power cord, or a problem at the RV inlet or main panel. This guide walks you through checking each one in order, so you can restore power or know when to call a technician.
Start With the Pedestal and Campground Power
Before touching anything on the RV, confirm the source is live. Campground pedestals can lose power from a tripped breaker, a neighboring site overload, or maintenance work. Plug a known working device, such as a lamp, into the pedestal outlet. If nothing lights up, the problem is not your rig. Try a different site if the campground allows it, or ask the office to check the pedestal.
Shopping for one? See our guide: 3 Best Norcold Rv Refrigerator Not Cooling But Has Powers (2026): Our Picks.
Check the Breakers and Shore Power Cord
If the pedestal is live, move to your RV. Look at the main breaker in the RV’s electrical panel and confirm it is fully on. Many RVs also have a separate breaker or GFCI reset near the inlet. Next, inspect the shore power cord from end to end. Look for melted plastic, discoloration, cracked jackets, or bent prongs. Overheated plugs often show brown or black marks around the blades. Any damage means the cord should be replaced, not taped.
Steps to follow
- Turn off all appliances and the RV main breaker.
- Unplug the cord from the pedestal and from the RV inlet.
- Inspect both ends for damage, corrosion, or loose contacts.
- Reconnect the cord to the pedestal first, then the RV inlet.
- Turn the RV main breaker back on and check the panel for power.
Test the Voltage at the Inlet and Panel
A basic multimeter tells you whether power is reaching the RV. Set it to AC voltage and check between the hot legs at the inlet, then between each hot leg and neutral. For a 30-amp RV, expect roughly 120 volts per leg and about 240 volts across the two legs. For a 50-amp RV, readings should be similar on each leg. A reading of zero on one leg suggests a broken conductor, a loose connection, or a tripped breaker on that side.
| Symptom | Likely cause |
|---|---|
| No power anywhere in the RV | Pedestal dead, main breaker off, or bad cord |
| Some circuits work, others do not | Individual tripped breaker |
| Power works, then cuts out | Surge protector or loose inlet connection |
| Burning smell or discolored plug | Overheated connection; stop and inspect |
Check the Surge Protector and Inlet Connections
Many RVs use an electrical surge protector or monitoring system between the inlet and the panel. If the unit shows a fault code, low voltage, or reverse polarity, it may be blocking power on purpose. Check the display or indicator lights and follow the manufacturer’s reset steps. Also inspect the inlet itself for scorched pins, loose wiring, or a cover that does not seal. Corrosion and loose terminals are common causes of intermittent power.
Common Mistakes
- Assuming the pedestal is live without testing it.
- Repeatedly resetting a breaker that trips immediately, which usually signals a fault.
- Using an adapter that overloads the pedestal or hides a wiring problem.
- Ignoring a warm plug or cord, which can be an early sign of a dangerous connection.
- Skipping the RV main breaker check after reconnecting.
Recommended gear
A digital multimeter lets you measure voltage at the pedestal and inlet so you can separate a campground problem from an RV problem. View on Amazon
A replacement shore power cord is the right fix when the original shows heat damage or cracked insulation. View on Amazon
A voltage monitor that plugs into the pedestal can flag low voltage, open ground, or reversed polarity before you connect. View on Amazon
FAQ
Why does my RV have no power but the pedestal works?
The most common reasons are a tripped main breaker, a faulty shore power cord, or a loose connection at the RV inlet. Check those three before assuming a bigger electrical problem.
Can a surge protector cause my RV to lose power?
Yes. A surge protector will cut power when it detects low voltage, high voltage, or wiring faults. Check its display and reset it according to the manufacturer’s instructions.
When should I call a professional?
Call a qualified RV technician or electrician if you find burn marks, melted plastic, a persistent burning smell, or no voltage at the inlet after checking the cord and breakers. Repairs to the RV’s wiring should be left to a professional. Worth reading next: RV No Power When Plugged In: 6 Causes and Fixes That Work.
Conclusion
When an RV is not getting power when plugged in, work from the outside in: confirm the pedestal, then the cord, then the RV breakers and inlet. Testing voltage at each stage quickly shows where the fault is. If you find heat damage or cannot restore power safely, stop and get professional help.

