Updated November 2026
When an RV shows no shore power, the problem is almost always somewhere between the campground pedestal and the coach’s inlet. This guide walks you through checking the pedestal, cord, inlet, and internal breakers so you can find the fault and restore power to your RV without guesswork.
Start With the Campground Pedestal
Before touching anything on the rig, confirm the source is live. Campground pedestals can be tripped, unplugged, or dead because of a neighboring site’s overload. Plug a lamp or a phone charger into the pedestal receptacle to confirm voltage. If nothing works, check the pedestal breaker or ask the campground office to reset it.
Shopping for one? See our guide: 5 Best 30 Amp RV Shore Power Cords for Campers (2026).
Check the Shore Power Cord and Connections
Once you know the pedestal is live, inspect the cord from end to end. Look for melted plastic, scorched prongs, cracked jackets, or loose connections at the plug and at the RV inlet. A damaged cord can cut power or create a hazard, so replace it rather than taping it. For details on selecting a replacement, see RV Shore Power Cord: How to Choose, Use and Care for One (2026).
- Unplug the cord from both ends.
- Inspect the plug, cord jacket, and inlet for heat damage or corrosion.
- Reseat the plug firmly at the pedestal and at the RV inlet.
- Try a known-good cord if you have one.
Inspect the RV Inlet and Receptacle
The inlet on the RV is a common failure point. Look for burn marks, discolored pins, or a loose fit. Corrosion inside the receptacle can block the connection even when the plug looks fine. If you see damage, the inlet needs replacement, not just cleaning. Understanding how the inlet connects to the coach helps you spot faults quickly; RV Shore Power Receptacle: How to Identify, Test and Use Yours Safely (2026) covers the testing process in detail.
Check the Main Breakers and the Converter
If the pedestal, cord, and inlet all check out, look inside the coach. Find the main breaker panel and confirm the shore power breakers are on. Then check the converter or power center. A failed converter can leave the coach without AC or DC power even when shore power is present at the inlet. Note that the power converter sits between shore power and your 12V system, so a fault there can look like a supply problem. If you suspect this, read Troubleshooting RV Power Converter: A Step-by-Step Guide for Campers.
Test Voltage Carefully
If you have a multimeter, measure voltage at the inlet with the cord connected. A healthy 30-amp system typically reads near 120 volts per leg, and a 50-amp system reads about 240 volts across the two hot legs. If you read zero at the inlet but voltage at the pedestal, the fault is in the cord or inlet. Work with the power off whenever you touch wiring, and if you are not comfortable working near live 120/240-volt circuits, call a qualified RV technician.
Common Mistakes to Avoid
- Assuming the pedestal is live without testing it.
- Using a damaged cord or taping a cracked jacket.
- Overlooking a tripped breaker inside the coach.
- Forcing a loose plug, which can burn the inlet.
- Mixing 30-amp and 50-amp adapters without checking the load.
Recommended Gear
- Digital multimeter: Lets you confirm voltage at the pedestal and inlet before you assume a fault. View on Amazon
- Replacement shore power cord: A matching cord is the quickest way to rule out a bad cable. View on Amazon
- Pedestal voltage tester: Confirms the campground outlet is live before you start troubleshooting. View on Amazon
FAQ
Why does my RV have no shore power but the pedestal works?
The likely causes are a damaged cord, a worn or corroded inlet, or a tripped breaker inside the coach. Check each in that order, starting with the cord and inlet.
Can a bad converter cause no shore power?
Yes. A failed converter or power center can cut AC and DC output even when shore power reaches the inlet, so test it after ruling out the cord and inlet.
When should I call a professional?
If you find burn marks, melted plastic, or unexplained zero voltage at the inlet, stop and consult a licensed RV technician or electrician. Working with 120/240-volt wiring carries real shock and fire risk.
Conclusion
Work from the outside in: pedestal, cord, inlet, then the coach’s breakers and converter. Most no-shore-power problems come down to the cord or inlet, and a methodical check will usually find the fault within minutes. When in doubt, replace the suspect part and retest.

