Updated November 2026
An rv power hookup voltage reading tells you whether the campground supply is safe to plug into. A healthy 30-amp or 50-amp RV hookup normally delivers about 120 volts on each leg, and 240 volts across the two legs on a 50-amp service. This guide shows you how to measure it, what the numbers mean, and when to unplug.
What Voltage Should You Expect at an RV Hookup?
Most RV manufacturers specify a nominal supply of 120 volts AC for standard appliances, with 240 volts available on 50-amp service. In practice, readings that fall roughly between 108 and 130 volts on the 120V side are generally considered acceptable by most RV owners and appliance makers, though your owner’s manual may list tighter limits. Readings outside that window, or a large difference between the two legs of a 50-amp service, deserve attention before you run anything.
Shopping for one? See our guide: Top 4 Midwest RV Power Pedestals for Campgrounds and Home RV Hookups.
How to Measure RV Power Hookup Voltage Step by Step
- Turn off all major loads in the RV, including the air conditioner, water heater and microwave, so the reading reflects the supply under normal conditions.
- Set a digital multimeter to AC volts, in a range above 240 volts.
- On a 30-amp plug, measure between the hot blade and the neutral slot, and between neutral and ground. Both should read close to 120 volts.
- On a 50-amp plug, measure hot-to-neutral on each hot leg, then hot-to-hot. Expect roughly 120 volts on each leg and about 240 volts between the two hots.
- Record the readings, then reconnect and test again under load if you suspect a problem.
Reading Your Results and Spotting Problems
A reading that is steady and close to nominal is a good sign. Watch for these patterns:
| Reading | What it may mean |
|---|---|
| Under about 105 volts | Low supply, often from long cable runs or an overloaded pedestal. Shut down heavy loads. |
| Over about 130 volts | High supply, which can damage electronics. Disconnect and seek another site. |
| Large gap between legs on 50-amp | Unbalanced supply or a loose connection. Stop and inspect the plug. |
| Near zero on one leg | Blown breaker or open connection at the pedestal. |
Voltage that sags when the air conditioner starts is common, but it should recover within a few seconds. A reading that stays low under load points to a supply or wiring issue, not your appliance.
Checking Ground and Polarity Before You Plug In
Voltage alone does not confirm the supply is safe. Use a polarity and ground tester plugged into the pedestal to check for reversed hot and neutral, an open ground, or a missing neutral. Any of these faults can cause shocks or damage. If the tester shows a fault, do not connect the RV. Ask the campground to correct it. For wiring work beyond checking, consult a licensed electrician or RV service technician.
Recommended gear
A basic multimeter lets you take readings at any site, and a plug-in polarity tester gives a fast go or no-go check. A surge protector sized for your RV’s service helps guard the coach if the supply spikes after you have checked it. Use the search phrases below to compare options.
- A digital multimeter with AC voltage ranges, useful for measuring each leg. View on Amazon
- A pedestal polarity and ground tester, which catches reversed wiring before you plug in. View on Amazon
- An RV surge protector, which cuts power if voltage moves outside safe limits. View on Amazon
Common Mistakes
- Testing with the air conditioner or heaters running, then assuming the supply is bad when it is actually normal under heavy load.
- Measuring only hot to neutral on a 50-amp service and missing a weak or unbalanced leg.
- Trusting a campground pedestal without checking, especially at older or busy sites.
- Using a cheap extension cord, which adds resistance and drops voltage at the RV.
- Ignoring a surge protector alarm instead of investigating the supply.
For more background on supply problems, see Rv Power Keeps Shutting Off: 6 Causes and Fixes for Campers and Standard Length of RV Power Cord: 25, 30 and 50 Foot Options Explained (2026).
FAQ
What is a safe rv power hookup voltage?
Readings near 120 volts per leg, with about 240 volts across the two legs on 50-amp service, are typical. Many owners treat roughly 108 to 130 volts as the acceptable window, but check your owner’s manual for the limits your RV specifies.
Can low voltage damage my RV?
Sustained low voltage can overheat motors such as air conditioner compressors and shorten their life. Shut down large loads if readings stay low, and consider a different site.
Do I need a multimeter to check the hookup?
A multimeter gives exact numbers, but a plug-in polarity tester catches wiring faults quickly. Many campers use both for a complete check before connecting.
Conclusion
Checking rv power hookup voltage before you connect takes only a few minutes and can prevent damage to your appliances and electronics. Measure each leg, compare the readings to the typical ranges above, and run a polarity check at the pedestal. When readings look wrong, unplug and ask for a different site or a repair.

