Updated November 2026

An RV shore power wiring diagram shows how the campground pedestal, the cord, the inlet and your coach’s electrical panel connect so that power reaches your outlets safely. Once you can read one, you can trace a fault, confirm your hookup is wired correctly, and spot the dangerous wiring problems that damage RV electronics. This guide walks through the standard layout for 30-amp and 50-amp service and the checks to run before you switch on.

Understand the Basic Layout of an RV Shore Power Wiring Diagram

Every standard RV shore power circuit uses the same core conductors, although the number of hot legs changes with amperage. A 30-amp connection uses one hot conductor (typically black), one neutral (white) and one equipment ground (green or bare). A 50-amp connection uses two hot legs (black and red), a neutral and a ground, which lets the coach run 240-volt appliances such as roof air conditioners at full capacity.

Shopping for one? See our guide: 5 Best 30 Amp RV Shore Power Cords for Campers (2026).

On a diagram, the pedestal or post is the source, the cord carries the power, and the inlet on the RV is where the cord connects to the coach. The main breaker panel, often called the distribution panel, then divides the incoming power into branch circuits. Reading the diagram left to right, from pedestal to panel, makes it much easier to follow.

Trace the Hot, Neutral and Ground Paths

Follow each conductor from the inlet to the breaker panel. The hot leg should land on the breaker bus through its main breaker, the neutral should land on the neutral bus bar, and the ground should land on the ground bar. On a 50-amp system, the two hot legs should each land on one side of the main breaker pair, so that each leg feeds half of the 240-volt load.

The most important rule is that neutral and ground stay separate inside the RV distribution panel and are only bonded together at the source. If your diagram shows a neutral-to-ground bond anywhere downstream, treat it as a wiring error. Problems like this are one reason shore power systems are checked with a tester before use. For a deeper look, Off Grid Solar Power System Wiring Diagram PDF: Step-by-Step Guide covers this in detail.

Check Polarity and Ground Before Connecting Power

  1. Turn off the pedestal breaker and make sure the RV main breaker is off.
  2. Plug in an inexpensive receptacle tester at the campsite outlet to confirm hot, neutral and ground are in the correct positions.
  3. Check that the inlet shows the same wiring as the diagram: hot on the expected terminal, neutral on the neutral terminal, ground on the ground terminal.
  4. Use a multimeter to confirm roughly 120 volts between each hot and neutral, and about 240 volts between the two hot legs on a 50-amp hookup.
  5. Only then switch on the pedestal and the RV main breaker, one step at a time.

If the tester shows reversed polarity, an open ground, or hot and neutral swapped, do not connect. Move to another site or have the pedestal checked by campground staff. Reversed polarity can damage electronics and create shock hazards.

Compare 30-Amp and 50-Amp Diagram Differences

Feature 30-Amp System 50-Amp System
Hot conductors 1 (black) 2 (black and red)
Neutral 1 (white) 1 (white)
Ground 1 (green or bare) 1 (green or bare)
Typical voltage 120 V 120 V and 240 V
Common use Smaller coaches, basic loads Larger coaches, roof A/C

Read the diagram for the plug or inlet you actually have. A 30-amp diagram will not show the second hot leg, and forcing a 50-amp cord into a 30-amp setup is a common source of confusion. For more on the connectors themselves, see RV Shore Power Plug: How to Identify, Wire and Use One Safely (2026) and RV Shore Power Receptacle: How to Identify, Test and Use Yours Safely (2026).

Common Mistakes

  • Assuming a diagram matches your coach without checking the actual inlet labels.
  • Skipping the polarity tester and trusting the campground pedestal.
  • Connecting a neutral-to-ground bond inside the RV panel, which can cause shock hazards.
  • Using an adapter to force a 50-amp connection into a 30-amp outlet.
  • Ignoring a worn or warm plug, which often points to a loose connection.

A plug-in receptacle tester lets you check polarity and ground at the pedestal before you commit to a hookup. View on Amazon

A digital multimeter confirms voltage between hot, neutral and ground, which is useful when a diagram and the real wiring disagree. View on Amazon

FAQ

Can I use the same wiring diagram for 30-amp and 50-amp RVs?

No. A 30-amp system has one hot leg, while a 50-amp system has two hot legs plus a neutral and ground. Always use the diagram that matches your inlet and breaker panel.

Why does my RV show reversed polarity at the campsite?

Reversed polarity means the hot and neutral conductors are swapped at the pedestal. Do not plug in until the site is corrected, because it can damage electronics.

Do I need an electrician to read my RV wiring diagram?

Reading a diagram and testing an outlet with a tester is something most RV owners can do. For faults, unclear wiring or any repair inside the panel, consult a qualified electrician or RV technician.

Conclusion

An RV shore power wiring diagram is simply a map of hot, neutral and ground from the pedestal to your breaker panel. Match the diagram to your 30-amp or 50-amp inlet, test polarity before you connect, and never bond neutral and ground inside the coach. With those checks in place, you can plug in with confidence.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our off-grid power for camping, RV & vanlife guides, checking product details against manufacturer specifications and owner feedback.