Updated November 2026

If your RV power jack is not working, you can usually find the cause in under an hour with a few basic checks. Most failures come from a tripped breaker, a damaged cord, a dead campground pedestal, or a loose connection at the inlet itself. This guide walks through those checks in order, so you can restore power or know when to call a technician.

Check the Campground Pedestal and Breaker First

Before touching anything on the RV, confirm the source is live. Plug a known-working device, such as a lamp, into the pedestal outlet, or check whether neighboring sites have power. Many campgrounds use shared breakers, and a single tripped pedestal can leave you without power while the rest of the loop is fine.

Shopping for one? See our guide: 3 Best Norcold Rv Refrigerator Not Cooling But Has Powers (2026): Our Picks.

Next, check the breaker inside the RV. Look at the main breaker panel and the shore power or converter breakers. A tripped breaker sits in the middle position, so push it fully off and then back on.

Inspect the Power Cord and Plug

A damaged cord is one of the most common causes of a dead RV power jack. Look along the full length of the cord for cracked insulation, scorched or discolored prongs, and bent or melted plug ends. Any heat damage is a serious warning sign.

If the cord is intact, try a different cord of the same amperage rating. Swapping cords quickly tells you whether the cord or the inlet is the problem. Our guide to Rv Replacement Power Cord: How to Choose and Swap One Safely covers matching ratings and replacing a worn cord.

Test the RV Power Inlet

With the cord unplugged from both ends, look inside the RV inlet for corrosion, bent contacts, or burn marks. Do not poke at energized terminals. If you have a multimeter and are comfortable using one, test for voltage at the inlet with the pedestal live and the breaker on. A healthy 30-amp inlet should read close to 120 volts between each hot leg and neutral, and between the two hot legs close to 240 volts.

No voltage at the inlet with live pedestal power points to a failed inlet, a broken wire, or a blown fuse or breaker in the path. If you are not sure how to read the results, stop here and call an RV technician. The steps below are a general guide, and work involving high-voltage wiring should be done by a licensed professional.

Tools You Will Need

  1. A multimeter rated for household voltage
  2. A flashlight
  3. A non-contact voltage tester
  4. Replacement cord or inlet, matched to your amperage
  5. Dielectric grease for cleaning and protecting contacts

Repair or Replace the Inlet

If the inlet shows corrosion, you can sometimes clean it with a contact cleaner and a small brush, then apply dielectric grease. If terminals are loose, burned, or cracked, replace the inlet entirely. Many owners find that a worn inlet causes intermittent power, where the RV works when the cord is wiggled and cuts out otherwise. You may also like RV Power Converter Not Working: 6 Steps to Diagnose and Fix It.

Replacement inlets are usually held in place by a few screws and connected with screw terminals. Turn off the breaker, confirm there is no voltage with your tester, and note which wire goes to which terminal before you disconnect anything. A photo helps.

Common Mistakes to Avoid

  • Assuming the RV is at fault without checking the pedestal and campground circuit.
  • Using an extension cord or adapter that is undersized for the RV’s amperage.
  • Ignoring a warm plug or discolored inlet, which can signal a dangerous connection.
  • Working on live wiring without first switching off the breaker and verifying zero voltage.
  • Forcing a cord into a damaged inlet, which can crack the housing and worsen the fault.

A basic multimeter helps you confirm whether voltage is reaching the inlet, which narrows down the fault quickly. View on Amazon

Dielectric grease protects clean contacts from moisture and corrosion after you service the inlet. View on Amazon

A non-contact voltage tester lets you confirm a circuit is dead before you touch any wiring. View on Amazon

FAQ

Why does my RV power jack work sometimes and not others?

Intermittent power usually points to a loose connection, a worn inlet, or a damaged cord that makes contact only in certain positions. Inspect and clean the inlet contacts, and test with a different cord.

Can I use an adapter if my RV power jack is broken?

An adapter can help you test or get temporary power, but it must match the amperage of your RV and the pedestal. Mismatched or undersized adapters can overheat, so use them only briefly and with care.

When should I call a professional?

Call a qualified RV technician or electrician if you find burn marks, no voltage at the inlet with live pedestal power, or if you are unsure how to test or replace the wiring. Electrical work carries real fire and shock risk.

Conclusion

Most RV power jack problems come down to the pedestal, the breaker, the cord, or the inlet, in that order. Work through those checks methodically and you will usually find the fault. When in doubt, or when you see heat damage, bring in a professional before you rely on that connection again.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our off-grid power for camping, RV & vanlife guides, checking product details against manufacturer specifications and owner feedback.