Updated November 2026
An anker car power inverter turns your vehicle’s 12V DC power into standard 120V AC outlets, so you can run laptops, phone chargers, small fans and other household devices while parked or on the road. This guide shows you how to match the inverter’s wattage to your devices, connect it safely to your battery or outlet, and avoid the mistakes that drain batteries or trip fuses at camp.
Step 1: Add Up Your Device Wattage
Start by listing every device you plan to run at the same time and reading the wattage from each label or power brick. Laptops often draw 50 to 90 watts, a small fan may draw 20 to 60 watts, and phone chargers usually draw 10 to 30 watts. Add these numbers together, then choose an inverter rated above that total, since most manufacturers recommend keeping continuous load at or below about 80 percent of rated output.
Shopping for one? See our guide: 7 Best Power Inverter Car Adapter Picks: Options Compared (2026).
Motors and compressors, such as a small cooler or a blender, can pull a surge several times their running wattage when they start. Check the startup rating if the device lists one, and leave extra headroom.
Step 2: Choose the Right Connection Point
Most anker car power inverter models plug into a standard 12V socket, which is convenient but limited by the fuse in that circuit, commonly around 10 to 15 amps. A 150-watt load draws roughly 12 to 13 amps from a 12V source once inverter losses are included, so a plug-in setup is fine for light loads but not for heavy ones.
For higher loads, connect the inverter directly to the battery with appropriately sized cable and an inline fuse close to the battery terminal. Our guide to Car Power Inverter Installation: A Step-by-Step Guide for Camping covers cable gauge and fuse placement in more detail.
Step 3: Connect and Test Safely
- Turn the inverter off and confirm the vehicle is off or the engine is running if you plan to draw heavy loads.
- Connect the inverter to the 12V socket or battery terminals, with the red lead to positive and black to negative.
- Switch the inverter on and check that its indicator light shows normal operation.
- Plug in a low-wattage device first, such as a phone charger, and confirm it works.
- Add devices one at a time, watching for warning beeps or a shutdown, which signals overload or low voltage.
Step 4: Manage Battery Drain at Camp
An inverter draws power continuously, even when the device plugged into it is idle, so it can slowly drain a starter battery. Turn the inverter off when you are not using it, and avoid running heavy loads with the engine off for long periods. If you camp for several days, a dedicated deep-cycle battery is a safer choice than your starting battery.
Common Mistakes to Avoid
- Running a space heater or microwave on a small inverter, which exceeds most plug-in limits.
- Leaving the inverter on overnight with the engine off, which can leave you unable to start the vehicle.
- Using thin wire or an undersized fuse on direct battery connections.
- Ignoring the low-voltage alarm, which is a warning to reduce load or start the engine.
- Placing the inverter in an enclosed space without airflow, where it can overheat.
Recommended Gear
- A fused battery cable kit: Keeps direct battery connections protected at the correct gauge for your inverter. View on Amazon
- A battery voltage monitor: Shows you how much charge remains so you can stop before the starter battery runs low. View on Amazon
FAQ
Can an anker car power inverter run a laptop while driving?
Yes, most laptops charge comfortably on a plug-in inverter while the engine runs, since the alternator replaces the drawn current. Keep the load well within the inverter’s rated output.
Will it drain my car battery?
It can, especially with the engine off. Turn the inverter off when not in use and monitor battery voltage during longer stops.
Is it safe to leave plugged in overnight?
Leaving the inverter on with no load still draws some current, so it is best to switch it off. If you have questions about your specific electrical setup, consult a qualified automotive electrician.
Conclusion
Choosing an anker car power inverter comes down to adding up your real device wattage, leaving headroom for startup surges, and picking the right connection point for your load. Follow the connection steps, keep an eye on battery voltage, and your campsite power will stay reliable for the trip.

